Hey Jude

Oh cool! Please would you post an image when you get a moment? Would be so cool to see it =D(Just look above the comments to the "I made it" button)

Nice guide - and congrats!If you add masking tape to the back of your rule, it skids less. (Not for you, but for noobs).=D

Have to say that is some nice detailing there....nice work!! =D

Yes, I doubt you'll squash a chicken, anymore than anyone can ever catch a pigeon! They may be dumb, but they are fast! But yes, for the sake of getting kids to appreciate 'safety in electronics and mechanics' it's a good problem to set kids. The counter sounds really tricky the more I think about it! xD Good luck!

Hiya, this is a nice project - thanks for sharing. I was wondering about that 350lb force on the actuator. I really doubt it *would* crush a chicken, they are pretty quick reflexed animals, and would be scatty at anything, so I get this is not a 'risk'. But it got me thinking how might you create a 'anti-crush' switch, just in case, (being at a school) a kid was sill enough to 'play chicken' with the closing door.... I was thinking something like a micro switch, but of course the floor could have debris so this could have a false trigger. I considered a light gate, but chickens being messy, might get left open. One could possibly use a train gauge, to stop if the resistive force peaked before door was shut but perhaps a bit elaborate? Lastly, I did think it might be fun to have a 'chicken…

Hiya, this is a nice project - thanks for sharing. I was wondering about that 350lb force on the actuator. I really doubt it *would* crush a chicken, they are pretty quick reflexed animals, and would be scatty at anything, so I get this is not a 'risk'. But it got me thinking how might you create a 'anti-crush' switch, just in case, (being at a school) a kid was sill enough to 'play chicken' with the closing door.... I was thinking something like a micro switch, but of course the floor could have debris so this could have a false trigger. I considered a light gate, but chickens being messy, might get left open. One could possibly use a train gauge, to stop if the resistive force peaked before door was shut but perhaps a bit elaborate? Lastly, I did think it might be fun to have a 'chicken counter', in that you could possibly count in/out the chickens....I imagined this might be a job for AI, as probably a light gate will fail, as chicken flock erratically and you may get 2 for 1, etc. Anyway, I get this is a fun project for a school, not an industrial piece of equipment (heck, they just pay a farmhand to do this!), but for the sake of kids and making it work with code, I thought it was a really nice 'extension' to see how the kids would solve this! Thanks again, and good luck!

This is a really clever hack - thanks for sharing! Good luck on Contest!

Oh wow - this is so cool that this has made it across the ocean and to new countries! And love the variations on the rule - thsi is very much what Mark and I hoped for!

So I've never heard of candle glue until now...why did you use this rather than say Hot Melt? I did look it up, but wondered why you specifically used it. What else is it good for? thx

Fluffy needs a 'Ghost Dog' - love it!! xD

Thanks so much - and glad you enjoyed the Backstory stuff also. =)

Thanks so much! Mark and I are very pleased indeed =)

Thank you - appreciate it! Nice when it all comes together in time!

Hey Julien,I guess you're new to Instructables contests - no problemo =) The good news is there is a TinkerCAD prize - in addition - to all the other prizes that don't need to use TinkerCAD. Think of it as a bonus prize!!If you're wondering why I added a note to the judges, it's because I uploaded the Goats and Llama CAD using TinkerCAD, but I stressed that they were not modelled in it. It was done in ZBrush, but it's useful to have it in TinkerCAD as it this is optimal for people in Instructables. So I was just being clear...Just to reassure you - no foul play ;o)This is in the finals as it qualifies as a boardgame. Hope this helps! Enjoy!

Thanks! I always worry that the 'epic' guide will intimidate people and put them off, but it's because I write steps on the basics, that it's so long. I think if you're good in the workshop, you probably just need like 5 steps! But I also know what it's like to be a noob, and you need the granular detail or it looks messy. Looking forward to seeing others make it tho - but it's certainly a full weekend (or more like 2 part time) project!

This is so great - nice pictures and guide as well. Looks great fun!

Good spot - thanks for that!! Updated now =)Glad you liked the game, please share with anyone else who might like it!

Whooop Whoop! Thanks =)

ICYMI - You don't *need* a 3D Printer, you can make it all from Card and Paper.

Looking very cool, Mark!

Thanks! I'm a bit of a 'Mutt', but I'll take it nonetheless. One day I will have a moustache like that :{

Yeah - now you got the Goat vs Llama FEVER!!

GREAT! And ICYMI, Mark just uploaded some 'no-3d-printer-necessary' game pieces, just so you have both options! Please share any pics in 'I Made It' section too!

I don't think you'll regret it. I actually WON my first 3D printer on Instructables many years ago with a Solder Buddy project. I now also have a Ender 3, which for c.$200/£185 is honestly a bargain, and works so well. I've used my loads. Thanks for the kind comments!

Joking, right? The Goat and Llama Gods have spoken, and they empower you to download it now, and build it, with (or without) 3D Printer!!!....at the next convenient opportunity ;o)

Thanks so much! Hope it's just 'thorough' and not intimidating...I tried to document it so people who were new to prototyping had support, but the pros can skip over it. Let us know if you give it a go, and/or share with someone who would also enjoy it? =)

Haha - thanks - glad you like it =)

Great guide. It's a small thing, but I love that you made the batteries visible. Great guide, and someone beat me to it to suggest glue on the burnt bits - but this is a small detail, and such a nice invention. My son's a bit older now, but would have loved this (I've also submitted a game for when you kid is older!! haha!). Will follow your future work! =D

Hi again, so personally, I rather liked that this was battery powered, and hence was not possible to run 24/7. I am no expert on circadian rhythms of birds, but I think it'd be unkind to run at night, right? (You'd be annoyed!!). Haha!That said, I googled if Birds can see IR, and apparently not, so if you were keen to would convert to IR Camera (Raspberry Pi has this for example). Hope this helps...

Hello - great that you're trying the project! I found that one of the key things here is not to have cats able to jump in to the 'flight path' of the approach to the Box. As for the WiFi setup, I have wondered if you could even use a solar panel, but I think it makes more sense to not run the device all the time, as the LEDs are quite warm over hours I suspect. The side window was bright enough for images, but in truth that one had not been nested in, so perhaps it's too 'weird' for them - but this is part of the fun of the experiment!

I found we can walk some distance away - like 10m easily. Our garden is not very large, so I can't say I've tested much more that that. But I saw this as a way to 'check in' on the birds rather than create a 24/7 setup. Hope this helps? =)

Hi - let me know if this all works out ok. 'Milnepe' has some good suggestions in comments. Thanks for bearing with us!

Hi there, sorry - I had login issue with this site. It should just gitpull and do an update - how far did you get with this?I did do it myself and it worked fine, and I have no special stuff. Mine is a RasPi4B.

Hi - sorry I had login issue with this site. Back now. It should be updated via the latest GitPull.

Yeah that’s true. It’s all updated now on GitHub. Perhaps try a Git Pull? Or if not update the json file.

That sounds great fun!! Good luck!

The Jog wheel is the little round thing on the right side.There is no 'scanner' as such, it is a list of stations paired with coordinates.Hope that helps =)

Hi - it goes to the nearest city. You use the Jog Wheel to scroll through. The update is coming soon with 15,000+ stations.

Thanks for uploading the picture - so cool! Like the funky buttons and reticule highlight. Looks very playful!

The 'correction' factor is an interesting one, I agree it depends on getting a nice globe. I got one from Amazon and it was way off, but for $10/£10 it's hard to expect perfection. To be fair I sent it back for a refund and got another an it was fine. I'd be inclined to perhaps 'centre' the 0,0 coordinate in such a way that it 'splits the different' of the general error of your globe. e.g. if things are a bit West-offset, centre with an East counter offset. If that makes sense?I'll certainly mention it in case it has an easy fix, but scaling the lookup table sounds tricky, as the distortion is also not constant. In an ideal world, you'd pick a 0,0 then say pick 10 major cities and calibrate on each of these, then the map would 'magically' interpolate between all of these. haha. I say that…

The 'correction' factor is an interesting one, I agree it depends on getting a nice globe. I got one from Amazon and it was way off, but for $10/£10 it's hard to expect perfection. To be fair I sent it back for a refund and got another an it was fine. I'd be inclined to perhaps 'centre' the 0,0 coordinate in such a way that it 'splits the different' of the general error of your globe. e.g. if things are a bit West-offset, centre with an East counter offset. If that makes sense?I'll certainly mention it in case it has an easy fix, but scaling the lookup table sounds tricky, as the distortion is also not constant. In an ideal world, you'd pick a 0,0 then say pick 10 major cities and calibrate on each of these, then the map would 'magically' interpolate between all of these. haha. I say that not being a coder. But in theory that is what 3D printers do with auto-levelling of the bed, so in principle it's possible, but of course more complex! I'll ask tho ;o)

Hello Markus!Please would you upload a photo to the section above! We'd love to see it =DRegards the issues, I know we have some bugs, but the good news is we have a Git update due any day now, and it's fixed a lot of that stuff - and we have not 15k stations!I'll ping here again when I get the approval from the Dev guys. (I'm just the idea guy - I don't do the smart bit! haha!).Looking forward to seeing the pictures! PS - May I ask what country you're from? Always curious as to where RadioGlobe finds a home ;o)

Great project - and love the aesthetic/black background!

I never knew this trick! Really cool. Thanks for sharing - super useful on some other projects I'm doing. I had usually just used heat guns, but this is far more controlled. Thanks!!

I love this so much! It's almost like those early experiements of computers trying to 'code' how life can evolve even with small instructions. Great work!

I see the DadJokes are strong with this one.

Lol - great video. Amazing what people can do with RC. xDThe attack sounds like something out of a Rick and Morty sketch...but does make you wonder what threat a Goose (much bigger) sees in a Duck? That said, I've noticed Coots will pick a fight with pretty much anything (I steered well away just in case). So much to learn about birds...

Good question. The fact is this is a ~$15 Boat, and the water sealing is not perfect. But the manufacturer has 'solved' in a good workaround and make the electronics encased in silicone to keep water out.I found that if I run it for 20mins (has a good battery life!), then perhaps 1-2cc of water gets in. But it empties out and does not affect the performance - but certainly sticking a tissue in before storage is wise. I've had it now for about 3 months (took a while to write up here - busy with work), and it's not rusted to a degree that stops it working. Again for the price - seems honest.

I hadn't until now! Yep gotta hand it to Knoxville and Co, they certainly have a lot of firsts. Hats off to them xD

Very kind. Glad they were clear (even if a bit long perhaps!)Please do post an image if you have a go!

Oh dear - sorry to hear about the Goose. I'm curious to know what month it was? As there were Geese on the water by the Boating Lake I was at (as well as Swans) and they were not bothered either way. I wonder if any ornithologists or twitchers reading this have any advice on best seasons to sail near water-foul to be most responsible to any given species? Of course best is to 'keep clear', but would love to know what is best practice.